Mosquito repellents like coils, mats, liquid vaporizers, creams are often used at various places. However, they are prone to be fatal and can cause harm to human beings. For instance, mosquito repellent creams and oils can cause adverse effects on the skin like allergic reactions. Coils, mats can produce toxic fumes when heated and cause breathing trouble, whereas liquid vaporizers can also produce fumes when heated.

For efficient results without any side effects, the most optimum solution is building a simple electronic circuit with minimal components which can produce output so as to repel the mosquitoes. In plain words, this article is going to describe a simple mosquito repellent circuit.

Principle Behind Mosquito Repellent Circuit:

Human beings can hear sound in the range of 20 Hz to 20 kHz. The sound of any frequency above 20 kHz is termed an ultrasonic sound. Several animals like cats, dogs, insects, mosquitoes have the feature of being able to hear this ultrasonic sound. In mosquitoes, this feature is attributed to the presence of sensory structures in their antenna.

Usually, an ultrasound is transmitted by male mosquitoes and received by female mosquitoes. However, after breeding, female mosquitoes generally avoid the ultrasound and this fact can be used to produce ultrasound in a range similar to that produced by male mosquitoes and repel away the mosquitoes.  The ultrasound produces stress on the antennae of the mosquitoes and repels them away.

In other words, a simple circuit is designed which can produce ultrasound in the frequency range of 20 kHz to 38 kHz, which can scare away mosquitoes.

Circuit Diagram of Electronic Mosquito Repellent Circuit: 

Electronic Mosquito Repellent Circuit Diagram

Electronic Mosquito Repellent Circuit Diagram

The most common form of Astable multivibrator is the 555 Timer IC. It is basically an 8 pin IC with the following pin description:

  • Pin1 – Ground pin, which is directly connected to the negative terminal of the battery.
  • Pin2- Trigger Pin. It is an active low pin. The timer is triggered when the signal at this pin is less than one-third of the supply voltage. For astable operation, this pin is connected directly to pin no.6
  • Pin 3 – It is the output pin.
  • Pin 4 – It is the reset pin. It is an active low pin. It is usually connected to the positive rail of the battery.
  • Pin 5 – It is the control pin and is seldom used. For safety purpose, this pin is connected to ground through a 0.01microFarad ceramic capacitor.
  • Pin 6 – It is the threshold pin. The timer output is back to its stable state when the voltage at this pin is greater than or equal to two-thirds of the supply voltage. For astable operation, this pin is shorted to pin 2 and connected to pin 7 using a resistor.
  • Pin 7 – It is the discharge pin and provides the discharge path for the capacitor.

Components Required

  • 555 timer
  • An electrolyte capacitor of 0.01 microFarad
  • A ceramic capacitor of 0.01 microFarad
  • A resistor of 760 Ohms
  • Another resistor of 1.5 K
  •  piezo buzzer
  • An SPST switch
  • A 5 V battery

Mosquito Repellent Circuit Design:

The basic idea behind developing the circuit is to use a buzzer to produce ultrasound. The buzzer is driven by an oscillator circuit. Here, we are using a 555 Timer based astable multivibrator circuit as the oscillator circuit.

Designing the circuit involves designing an astable multivibrator circuit. Generally, the frequency of output signal produced by a 555 astable multivibrator is given by:

F = 1.44((Ra+Rb*2)*C)

Here Ra is the value of resistor between pin 7 and Vcc, Rb is the value of the resistor between pins 7 and 6 and C is the value of capacitor between pin 6 and ground.

Let C = 0.01 microFarad

F = 38 kHz

Let Duty Cycle, D = 60% (It is not possible to get 555 timers to produce signal with 50% duty cycle.

This gives,

Ra = 1.44(2D-1)/(F*C)

And Rb=1.44(1-D)/(F*C)

Substituting values of C, F, and D, we get

Ra = 0.758 K Ohms, i.e. 758 Ohms and Rb = 1.52 K Ohms

Thus, we can use a resistor of 760 Ohms and another resistor of 1.5 K. Here a potentiometer of 1.5 K is used.

Theory Behind the Circuit:

  • A multivibrator is an electronic circuit producing a pulsed output signal. Generally, multivibrators are classified based on the nature of the stability of output.
  • A multivibrator with one stable state is known as a monostable multivibrator and is used as a pulse generator.
  •  A multivibrator with no stable state is known as an astable multivibrator and is used as an oscillator.
  • A multivibrator with two stable states is known as a bistable multivibrator and is used as a Schmitt Trigger.

Here we are mainly concerned about Astable multivibrator. Astable multivibrators do not require any external triggering and hence can be used as oscillators. They are realized using transistors, operational amplifiers or ICs.

Mosquito Repellent Circuit Operation:

Once the switch is closed, the 555 timer gets the power supply. As per the inner circuit, initially the capacitor voltage will be zero and hence the voltage at threshold and trigger pin will be zero. As the capacitor charges through resistors Ra and Rb, at a certain point voltage at the threshold pin, is less than the capacitor voltage. This causes a change in timer output. The capacitor now starts discharging through resistor Rb, i.e. the discharge pin and continues so until the output voltage is back to the original. Thus the output signal is an oscillating signal with frequency 38 KHz.  The output from this astable multivibrator circuit drives a 38 KHz piezo buzzer, producing ultrasound at regular repetitions. On varying the value of the potentiometer, the output frequency can also be varied.

Applications of Mosquito Repellent Circuit:

As described, this circuit can be used as a mosquito repellent. By certain modifications and changes in the value of resistors and capacitor, the circuit can also be used as another insect repellent. Further, it can also be used as a simple buzzer alarm circuit.

Mosquito Repellent Circuit Limitations

  • It requires a lot of frequency setting.
  • Ultrasound signals travel at an angle of 45 degrees from the source. In case of any obstacles in the path, the signals get reflected or diverted.
  • It shows an effect for lesser mosquito population.


Please enter your comment!
Please enter your name here